Division Works

	DIVISION 6 - WOOD AND PLASTICS
	06100 - ROUGH CARPENTRY
	06400 - ARCHITECTURAL WOODWORK
	Supply & install the following custom made wooden Items and furniture including hardware, backing, mounting, accessories & specialties, all as described
A	Reception Welcome Counter Desk at Ground floor, size approx 2100 x 750 x 900 mm high; consisted of the following:
	1- Glacier white corian desk top with 30mm thick finished edges with  all necessary 80mm dia cable ports - (Code 15)
	2- Curved glass modesty panel nominal 10mm thick, toughened finish with polished edges and frosted crystal film to back face - (Code 06)
	3- CPU cradle fixed to the bottom of the desk top
	4- Drawer pedestal with white corian front, finger-grip profile to drawers, and all other surfaces in white laminate; including drawer interiors, in addition to pull out printer shelf and runners 450mm ball bearing 100% extension soft close
	5- Satin stainless steel support leg size 50 x 50 mm - (Code 07)
	6- Deck under the task chair connecting between the desk and the back low partition, size approx 2100 x 790 x 150 mm high; built up in double layers of 22mm thick plywood fixed on 100 x 100 mm white soft wood beams fixed to the screed floor, sides of this deck are covered by Oak laminate plinth edges with aluminum protective corners angle; type light Oak effect Formica F5374 elegant Oak - (Code 01), top surface of this deck is covered by feature striped carpet tiles; Forbo Tesera xn25 - (Code 24)
	7- Curved desk front, side and back, built up in 25mm thick slats, edges in light Oak laminate, 5 x 5 mm shadow gaps finished in white laminate
	Refer to Standard details no.DV6-WP-1,2,3, for all necessary details
B	Ditto but at first floor as per drawing
	refer to standard details  no.DV6-WP-1,2,3, for all necessary details
	TO COLLECTION     KD
A	Welcome Wall at Ground floor, consisted of the following:
1	Curved glacier white corian front and back with light Oak laminate edges fixed to 22mm thick plywood fixed on 50 x 50 mm white soft wood substructure - (Codes 01 & 15)
2	Curved low wall built up in 50 x 50 mm white soft wood substructure underneath 9mm thick plywood on both sides and covered by 25mm thick slats on both sides, edges is light Oak laminate and 5 x 5 mm shadow gaps finished in white paint or laminate with 30mm thick top capping in glacier white corian with 3mm rad all edges
3	Lighting channel, concealed LED strip light profile, high output 36 x LED/m to reduce 'starring' effect, covered by opal acrylic diffuser
4	Perch seat, 50mm high density foam on 22mm panel, bright Red fabric upholstery, fabric to be even with no stretching; Kvadrat Topas 2 :604 - (Code 10)
5	Recess into the curved wall face to contain a 60" monitor, flat section of wall 50mm high above and below the monitor to ensure monitor does not protrude beyond wall, allow 20mm clear all around and sufficient depth for VESA mounting bracket, requirements for data, power and ventilation TBC by M&E/AV subcontractor.This recessed wall is finished in signal white laminate RAL 9003 F2255 polar white matt - (CODE 03)
6	Boubyan graphics, laser cut 5mm mirror polished aluminum offset  5mm for 3D effect, 'Arch' motif in red powder coat Graphic placement = LH of logo is aligned with LH edge of monitor cutout - (Code 16)
7	PLATINUM graphics with red arch to letter 'A' in 5mm laser cut mirror polished aluminum - (Code 16)
8	15 x D3 Sized brochure display, crystal white measured separately
	Refer to Standard details no.(DV6 - WW-1,2,3), for all necessary details